Flowers and vegetables may be affected by chlorinated water. The water supply should now be bacteria free. It may take several treatments to remove long-established bacteria colonies. If the problem persists, contact a professional familiar with microbiological contamination in wells.
Water Volumes in Various Diameter Wells. Skip to main content. Search form Search. Test for chlorine indoors. Go inside and test for the presence of chlorine at every sink bath and shower, using either the test kit or your sense of smell.
You should also flush each toilet in the house once or twice. Wait 12 to 24 hours. Leave the chlorine to sit in the water supply for a minimum of 12 hours, but preferably During this time, do your best to keep water use to a minimum.
Part 3. Set up as many hoses as possible. After 24 hours, your water will be completely disinfected and you can begin the process of removing chlorine from your water supply. To do this, attach as many hoses as you have outdoor spigots and tie the ends around a tree or fence approximately three feet off the ground.
This makes it easier to monitor the water flow. Don't run the water anywhere near the septic tank or leach field, as you don't want to expose these areas to the chlorinated water.
Run the water at full force. Turn on each of the spigots and run the water as hard as possible. Try to direct the stream of water into a ditch or somewhere the water will be somewhat contained. Test for the presence of chlorine. Periodically check the water coming out of the hoses for the presence of chlorine. Use the chlorine test kit for this, as you may be unable to detect small quantities of chlorine by smell alone.
Don't allow the well to run dry. Boring as it may be, it is important to keep an eye on the water flow at all times, to ensure that the well doesn't run dry. If the well runs dry, the pump may burn out, and these can be very expensive to replace.
If it looks like water pressure is dropping off, turn off power to the pump and wait an hour before resuming the run-off. This gives the well a chance to refill itself. Only stop the water flow when all traces of chlorine have been removed -- this may take as little as two hours or much longer, depending on the well. Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow.
Anthony "TC" Williams. Support wikiHow by unlocking this expert answer. Not Helpful 4 Helpful Not Helpful 8 Helpful Leave your hot water heater in normal mode, flush the tank by connecting a hose to the drain, or by simply running the taps. Do this after flushing the chlorine out of the rest of the lines, to limit the amount of chlorine running to your septic tank. Put the softener and sediment filter in bypass during this procedure, and replace your sediment filter while you are at it.
Not Helpful 13 Helpful Can the 3" tablets used for swimming pools and aerator systems be used when chlorinating a well?
They accumulate stabilizing compounds that are not healthy to drink long term. Not Helpful 12 Helpful Keep pumping through your outdoor spigots. Minimize chlorine in your septic system. Not Helpful 3 Helpful I used a fishing line to drop a fishing weight into a drilled well to test the depth, but the weight got stuck inside the well.
How I can get the weight back up? There isn't really an easy way to get the weight back. You could try dropping a bucket down into the well and scooping it up.
Not Helpful 11 Helpful If water reaches the ground surface under the natural pressure of the aquifer, the well is called a flowing artesian well. An aquifer is a geologic layer of porous and permeable material such as sand and gravel, limestone or sandstone through which water flows and is stored. Most water treatment equipment such as water heaters, softeners, and pressure tanks , should also be disinfected.
Some water filters, such as carbon filters, should be temporarily disconnected or by-passed during shock chlorination. Check owner's manuals or manufacturers' literature before shock chlorinating to avoid damage to components.
Use liquid household bleach containing 5. Do not use bleach with a "fresh scent," lemon fragrance, or other cleaners added. One gallon of bleach will treat up to an 8-inch diameter well containing feet of water.
If your well is much larger, or if your distribution system is unusually large, expect to use more than 1 gallon of bleach. Avoid direct skin contact with bleach solutions. Wear rubber gloves, goggles, and a chemical-resistant apron when handling bleach. If it accidentally gets on your skin, flush immediately with clean water. Never mix chlorine bleach with other cleaners; it may produce a toxic gas. Some chlorine may persist in the system for days. Water with a slight chlorine smell should be usable for most purposes.
When the water table is lowered due to pumping of groundwater, the sediments in groundwater are exposed to oxygen. Oxygen helps in dissolving some of the arsenic contained in sediments. Similarly, because chlorine is a strong oxidant, it could dissolve arsenic from sediments and release it into the groundwater.
Shock chlorination is used to remove bacterial contaminants from well water, well casings, holding tanks and the whole water supply system. A licensed well driller is trained to shock chlorinate. Should you decide to shock chlorinate your well yourself, take the following precautionary measures:.
Wait one to two weeks after shock chlorinating the water supply system to retest for total coliform and E. Follow sample collection instructions carefully. If the test results show the absence of coliform bacteria, the water is safe to drink.
0コメント